BestEquip Топлообменник 3x7,5 40 пластини Запоен пластинчат топлообменник 316L 3/4 MPT Топлообменник B3-12A Охладител за бирена мъст за хидравлично отопление

Brand:BestEquip

3.4/5

lv
224.95

Много гъвкав: Тази бира с топлообменник предлага най-високо ниво на термична ефективност и издръжливост в компактен и лек модул, идеален за промишлено охлаждане на масло, изпарители на хладилен агент и кондензатори, жилищни и леки търговски HVAC хидравлични системи. Компактен дизайн: Дизайнът на гофрираната плоча на тази плоча за охлаждане на пивната мъст позволява значително по-малка конструкция и отпечатък при еквивалентна или по-добра производителност в сравнение с други устройства за пренос на топлина – което води до значително спестяване на пространство. Здрава конструкция: Този 40 пластинчат топлообменник включва листове от неръждаема стомана 316L, които са запоени заедно в ръбовете и матрицата от контактни точки за надеждна и здрава част, за да образуват издръжлива, интегрална част, която може да издържи на високо налягане и температура. Четири удебелени MNPT порта за вашата по-лесна инсталация. Оптимизиран за енергия: Този неръждаем топлообменник може да загрява вода до предварително зададената температура, което е супер енергоспестяващо без консумация на електричество и кислород. Висока термична ефективност: Дизайнът с турбулентен поток движи двете среди в противоположни посоки и създава силни турбуленции за превъзходни скорости на пренос на топлина и ефективност. Нашите серии топлообменници са сертифицирани от CE.

Няма налични единици
Много гъвкав: Тази бира с топлообменник предлага най-високо ниво на термична ефективност и издръжливост в компактен и лек модул, идеален за промишлено охлаждане на масло, изпарители на хладилен агент и кондензатори, жилищни и леки търговски HVAC хидравлични системи. Компактен дизайн: Дизайнът на гофрираната плоча на тази плоча за охлаждане на пивната мъст позволява значително по-малка конструкция и отпечатък при еквивалентна или по-добра производителност в сравнение с други устройства за пренос на топлина – което води до значително спестяване на пространство. Здрава конструкция: Този 40 пластинчат топлообменник включва листове от неръждаема стомана 316L, които са запоени заедно в ръбовете и матрицата от контактни точки за надеждна и здрава част, за да образуват издръжлива, интегрална част, която може да издържи на високо налягане и температура. Четири удебелени MNPT порта за вашата по-лесна инсталация. Оптимизиран за енергия: Този неръждаем топлообменник може да загрява вода до предварително зададената температура, което е супер енергоспестяващо без консумация на електричество и кислород. Висока термична ефективност: Дизайнът с турбулентен поток движи двете среди в противоположни посоки и създава силни турбуленции за превъзходни скорости на пренос на топлина и ефективност. Нашите серии топлообменници са сертифицирани от CE.
Batteries Required? ‎No
Color ‎Sliver
Country of Origin ‎China
Customer Reviews 4.4 4.4 out of 5 stars 128 ratings 4.4 out of 5 stars
Included Components ‎1 x Heat Exchanger, 1 x A Pair of Hoops
Item model number ‎BestEquip Heat Exchanger
Item Package Quantity ‎1
Item Weight ‎5 pounds
Manufacturer ‎BestEquip
Material ‎Metal
Number Of Pieces ‎1
Part Number ‎BestEquip Heat Exchanger
Product Dimensions ‎8.3 x 7.1 x 3.9 inches
Size ‎40

3.4

13 Review
5 Star
71
4 Star
15
3 Star
3
2 Star
4
1 Star
7

Напишете вашето мнение

Вашият имейл няма да бъде публикуван. Всички задължителни полета са маркирани с*

Scritto da: tammy kowitz
Help
I really need to return this and the return window closed yesterday! I can’t find the right size fitting threads
Scritto da: Michael Voigt
Cools wort, doesn’t leak, seems legit.
I use this as a wort chiller. When I switched from an 8 gallon kettle to a keggle, my copper coil was physically too small to use and still have the connections outside of the kettle. After I had a hose blow off my coil and get tap water in my nearly chilled wort, I decided to find a better way. The nice thing about a plate chiller is that it is so small that you don’t need to handle or store it. I have mine clipped right next to my kettle, and all I have to do when I want to use it is hook up my hoses. I’m going to exbeeriment with using it during my eBIAB mash to heat sparge water to mash temps. As far as cleaning goes, I’ve found that it really helps to alternate back and forward flushing hot PBW through it until it runs clear, then repeat with water. Time will tell how clean it stays. As far as performance, it gets my 5 gallon batch of wort from boiling, down to pitching temps in about 30 minutes on tap water. I was hoping for faster cooling than that, but I’m going to tweak my technique a little and see if I can avoid recirculating it back into my kettle. If I set it up right, it should come out at pitching temperature. That should shave some time off my brew day.
Scritto da: Michael Miller
Works better than expected, fastidious cleaning after use highly suggested
I use this product to cool the wart of my beer. I have to admit it exceeded expectations! With my ground temperature water, it was able to cool down 6 gallons of 210 degree wort to 65° in under 5 minutes. I couldn't believe it! This thing got it done so fast it was ridiculous. Highly recommend it. Be aware of that you have to be very fastidious in your cleaning after cooling your wort.
Scritto da: Cory A Kratzer
Works great
Chills wort within 30 minutes
Scritto da: bbnj
Good value
Used to add radiant floor heat using my on demand water heater. Worked perfectly.
Scritto da: Daniel M Murillo
Decent job transferring heat
This plate chiller is used for my 10 gallon brewing system. I have a couple of pumps I use to run water and wort through the chiller. It gets 10+ gallons of boiling wort to under 100 degrees in about 15 or 20 mins, then takes another 10 or 15 to get under 80, mostly due to hot TX water and not having enough ice on hand. But overall the chiller does a decent job of transferring the heat. I just wish the water ports were fitted for garden hose. Not a big deal, I just hooked up some quick disconnects and bought an adapter for my garden hose. Also, I’d like the brackets to be a little longer as they seem to bend slightly trying to cinch them down- again though nbd.
Scritto da: Steve Raabe
Fittings are very close together so you cannot use 90 degree fitting on all 4
100% heat transfer fitting are to close in order to use 90degree fittings on all 4
Scritto da: Rickey M. Horwitz
Excellent Value and Very Good performance
I purchased this to replace my 30 plate chiller and it works almost twice as good without spending twice the money. As other people pointed out, it has four 1/2 FPT fittings, so you will need to buy a FPT to hose bib m/f for the cold water side.
Scritto da: Gary williams
Used for swimming pool
Used this to heat my 12 foot swimming pool, can get the pool to 40c from the central heating if I want! Left it turned on with no control, that’s how I know. Controls and stats now fitted, sits perfect at 30c now great item
Scritto da: Cliente Amazon
Soddisfatta
E stato il miglior acquisto dell’anno . Visto il caro bollette abbiamo pensato di aggiungere alla nostra caldaia questo scambiatore .. e va benissimo ! Poi il prezzo non ne parliamo .. OTTIMO ???? C’è lo siamo però fatti istallare da un idraulico per essere più tranquilli !
Scritto da: Marco
Riscaldamento acqua sanitaria
Prova per riscaldare acqua con stufa a pellet riuscita????????
Scritto da: Massimo fogli
Ottimo prodotto
Ottimo prodotto
Scritto da: andrea
Pessimi
Non comprerò mai piu

Свързани продукти

Открийте нашата международна мрежа

Изпращаме до 28 държави, над 200 000 продукта. Бъдете в течение, абонирайте се за бюлетина.

Array