UltraPro Z-Wave Smart Toggle Light Switch with QuickFit and SimpleWire, 3-Way Ready, Съвместим с Alexa, Google Assistant, ZWave Hub Required, Repeater/Range Extender, Бял, 2 пакета, 54912 2 пакета Light Switch Switch Бял превключвател

Brand:UltraPro

3.5/5

lv
192.52

Останете свързани с дома си с UltraPro In-Wall Smart Switch. Съвместим с всички Z-Wave сертифицирани шлюзове, интелигентният превключвател ви дава безжично управление на кабелните ви светлини от всяко мобилно устройство, компютър или дистанционно с активиран Z-Wave. Инсталирането е лесно – просто заменете стандартен стенен ключ с интелигентния ключ. Независимо дали сте у дома или навън, използвайте превключвателя, за да включвате и изключвате осветлението. Интелигентният превключвател не само помага за намаляване на разходите за енергия, но повишава безопасността на вашия дом, като поддържа стаите да изглеждат светли и обитаеми. Вашият интелигентен дом стана по-умен с UltraPro In-Wall Smart Switch.

СЪВМЕСТИМОСТ - Работи с всички LED, CFL, халогенни крушки, крушки с нажежаема жичка и други устройства. ИНСТАЛИРАНЕ В СТЕНА С ТВЪРДИ КАБЕЛИ ВРЪЗКИ (ИЗИСКВА СЕ НЕУТРАЛЕН ПРОВОД) – Сменете съществуващия стенен превключвател само за 15 минути – Стенната плоча НЕ е включена. Необходим е неутрален проводник – моля, потвърдете, че окабеляването във вашия дом е съвместимо, преди да закупите (по-старите домове може да нямат неутрални проводници). СЪВМЕСТИМ С ALEXA (ИЗИСКВА СЕ ХЪБ) - Изисква поддържан от Alexa хъб за гласово управление с продукти на Amazon Echo (устройството и хъбът на Alexa се продават отделно). Не може да се свързва директно с ECHO PLUS (Само ZigBee продуктите могат да се свързват директно с Echo Plus). ИЗИСКВА СЕ СЕРТИФИЦИРАН Z-WAVE ХЪБ - Съвместим със следните Z-Wave хъбове: Honeywell, Ring, SmartThings, Wink, HomeSeer, Fibaro, Trane, Nexia, ADT, Vera и др. БЕЗЖИЧНО УПРАВЛЕНИЕ И ГРАФИК НА СВЕТЛИНИТЕ И ДРУГИ УСТРОЙСТВА – Планирайте събития с времеви график за свързани устройства. Персонализирайте сцени за деня или нощта, у дома или навън. Безжично управлявайте превключвателя от всяко място чрез вашия смартфон, таблет, компютър или Z-Wave дистанционно. Превключвателят може да се управлява ръчно.
Brand UltraPro
Connector Type Clamp
Contact Type Normally Open
Country of Origin China
Current Rating 15 Amps
Item Dimensions LxWxH 1.92 x 2.14 x 4.15 inches
Item model number 54912
Manufacturer Jasco Products Company, LLC
Material Polycarbonate
Operating Voltage 120 Volts
Operating Voltage 120 Volts (AC)
Operation Mode ON-OFF
Product Dimensions 1.92 x 2.14 x 4.15 inches; 8.78 Ounces
Switch Type Toggle
Terminal Screw

3.5

8 Review
5 Star
73
4 Star
13
3 Star
6
2 Star
3
1 Star
5

Напишете вашето мнение

Вашият имейл няма да бъде публикуван. Всички задължителни полета са маркирани с*

Scritto da: R. Levy
Very easy to integrate with SmartThings!
Open the SmartThings app and scan the sticker on the switch before you install. SmartThings will recognize the switch (although it called it a GE switch). Then once it powers up there is nothing more to do. SmartThings sees the switch and then you can integrate with whatever Home app you use with your SmartThings devices. I didn't have to do any toggles etc. as is sometimes necessary with these devices in order to find the device on the Z-wave network. For those that are interested, I installed this one in a housing box as pictured. The only problem was that the metal backplate on the switch was too large for this type of install, so I hacksawed it to align with the housing. Otherwise a straightforward install to replace an old Intermatic mechanical switch that is pretty outdated given the routines you can set up in SmartThings. I've installed a number of Zwave switches and although I can't speak yet to the reliability of this switch I did find that the initial set up was easier than some other devices.
Scritto da: Zeph
Same Hardware as GE, better price
These are the same Jasco Z-Wave switches that GE uses in their kit, just at a much better price. They integrated with HomeAssistant with no problems.
Scritto da: Diyengineer
Works so far
Purschased this to replace bad ge smart switches. Hoping these will last longer then ge brand. Also price is much better. Installation was easy and no hassle adding to smart things app.
Scritto da: Joe
Good ol Zwave.
Was looking for a replacement for an older GE jasco zwave switch that got toasted in a power outage. This one fit the bill. Was an exact match to the old one. And learning it was easy. Will buy again if I decide to Add more smart switches.
Scritto da: Jay_ATX
Works as good as GE and is compatible with Ring Alarm!
I needed to add some additional Zwave switches to my home but wanted something cheaper than the GE switches I had. These switches work the same as GE and are made by Jasco who also makes the GE Enbrighten switches. These also have a smaller profile than my original GE Zwave switches and paired easily to my Ring alarm. Installation was straightforward and took
Scritto da: toolseller
How to pair with SmartThings
For the SW4009 version, do the steps below to save hours: 1) Wire it up and install but leave faceplate off 2) do a factory reset even though it's new, flip toggle up 3 times, then down 3 times 3) in SmartThings app, find ur hub, select menu->Z wave utilities->z wave exclusion->flip toggle up and maybe down to get device excluded message. Maybe repeat...getting it excluded is KEY! 4) From a "room" in the app, select add a device. Browse by type->switch/dimmer->GE->GE z wave->next... 5) momentarily flip toggle up, then maybe down, and maybe repeat... usually works first time. You're not holding the toggle for this or any steps in this guide. 6) enter PIN from switch when prompted for the security function (u left cover off didn't u???).. don't bother trying to scan... 7) Success!!! Or try again from factory reset. You can now rename, move to another room, etc. 8) LED backlight is controlled in the Smart Things app. Select the switch and you can open the menu for the switch to control LED backlight function. I couldn't get it to work via directions provided with the switch by toggling the toggle. Finally, I've gotten a couple different versions of the "same item". This is what I FINALLY got to work with the noted part number. Factory reset and excluding from hub before adding to a room appear to be the key. Usually u don't have to keep toggling to get to pair but sometimes it helps, as does moving your hub close to the switch. If u can get the device excluded, ur well on ur way to success.
Scritto da: LearningMonkey
Same as GE for a lot less!
I saw these and thought this might be a cheaper option than the GE Embrighten switches that I have been getting. Not only are they cheaper, but they are EXACTLY THE SAME! I am pretty sure these are the exact same switches made by Jasco that GE offers. Features in the postings match up, they install in Smartthings as GE switches, and the printing/graphics on the face of the switch are the same! At $10 less per switch I will be getting these exclusively now. Thanks Ultra-Pro!
Scritto da: Myles
Switch was easy to install No customer service to help with software light switch integration!!!
Switch was easy to install No customer service to help with software light switch integration!!! On this I do not recommend this product!

Свързани продукти

Открийте нашата международна мрежа

Изпращаме до 28 държави, над 200 000 продукта. Бъдете в течение, абонирайте се за бюлетина.

Array