T-H Marine 13022 Адаптер за скоба за накланяне и тримиране

Brand:T-H Marine

3.5/5

lv
440.76

Този адаптерен комплект е направен за бърз и лесен монтаж на двигатели с избран тип транцева скоба. Някои двигатели са твърде големи за по-малките наклонени и облицовки или жак плочи, но те се нуждаят от адаптер, за да се поберат на по-големи плочи; това са адаптерните пластини.

Няма налични единици
Консултирайте се с вашия местен дилър, за да се уверите, че е подходящ за вашата лодка. Използвайте с PT-130 / THT-130C за монтаж на по-малки двигатели, монтирани с транцеви скоби. Работи с CMC PT-130 наклон и трим, ATLAS THT-130C наклон и трим.
Brand ‎T-H Marine
Country of Origin ‎China
Customer Reviews 4.4 4.4 out of 5 stars 30 ratings 4.4 out of 5 stars
Is Discontinued By Manufacturer ‎No
Item model number ‎3002.1020
Item Weight ‎2 pounds
Manufacturer ‎T-H Marine
Manufacturer Part Number ‎3002.1020
Model ‎13022
Product Dimensions ‎17.99 x 5 x 2.01 inches

3.5

8 Review
5 Star
74
4 Star
12
3 Star
5
2 Star
0
1 Star
9

Напишете вашето мнение

Вашият имейл няма да бъде публикуван. Всички задължителни полета са маркирани с*

Scritto da: Amazon Customer
Perfect fit adapter set
Perfect adapter set for my outboard motor and the tilt unit I bought for it
Scritto da: William T. Alvord
The description was a little foggy but it seemed like it might work
Did the trick perfectly. I have a boat with a 15" transom and a CMC PT-130 tilt / trim unit. I got a new Suzuki 25 that has a clamp on type transom mount and what I assume is a nonstandard mounting bolt pattern. I say this because nothing lined up bolt wise, and even if I used the clamps and then drilled and bolted the lower mounting holes, the engine would set way too low. Before reinventing the wheel, I looked at the CMC site and saw this adaptor. The description was a little foggy but it seemed like it might work. Low and behold, Amazon not only stocked it, but it was prime. Knowing I could send it back if it didn't work, I went for it. Not only did it raise the engine, but it's very sturdy and I'm sure it will last a long time. I don't know why the description says it only weighs 2 pounds because it weighs more like 10. Came with stainless 1/2" mounting hardware. I very happy I got this and didn't try to jury rig something.
Scritto da: Bills Boats.
Does not fit mercury Inline 6
Do not buy for inline 6 with clamps unless you want to spend hours drilling it. The holes do not line up at all in order to bolt the motor to the plate. I had to custom drill through inches of solid metal in order to run a bolt through the motor and plate. They should give better instructions before you buy on how to Mount a motor to the plate
Scritto da: Greg Rawn
Requires a shim to clamp motor on
Easy to install, but my transom clamps ran out of thread without getting snug, requiring a 5/8" shim.
Scritto da: Brant Lindsey
Great product
It worked perfect and fit my 40hp yamaha outboard
Scritto da: Mary Kiehn
Couldn't fine enough information to know if I needed it
Looks good but never needed it. Not enough information to know for sure.
Scritto da: Joseph Denton
Very strong and fast delivery
Great product at good price
Scritto da: RB
Four Stars
Met expectations.

Свързани продукти

Открийте нашата международна мрежа

Изпращаме до 28 държави, над 200 000 продукта. Бъдете в течение, абонирайте се за бюлетина.

Array