Среден вентил EVGG0200-OM Диелектричен съединителен тръбен фитинг 2 инча FIP Намалява електролизата Месинг x Неръждаема стомана 2 FIP

Brand:Midline Valve

3/5

lv
200.64

както се изисква от водопроводните кодекси. съответствие: astm f492-95; ISO:9001; без съдържание на олово; оценени до 230°f. разполага със сигурни 2-инчови връзки без течове. превъзходно качество: изключително издръжлива конструкция от месинг x стомана. безопасност: тези фитинги за тръби ще избегнат електролизата между различни метални тръби, като по този начин ще намалят корозията и повредата на тръбите във вашите тръбни системи. идеален за приложения с бойлер.

Няма налични единици
както се изисква от водопроводните кодекси. съответствие: astm f492-95; ISO:9001; без съдържание на олово; оценени до 230°f. разполага със сигурни 2-инчови връзки без течове. превъзходно качество: изключително издръжлива конструкция от месинг x стомана. безопасност: тези фитинги за тръби ще избегнат електролизата между различни метални тръби, като по този начин ще намалят корозията и повредата на тръбите във вашите тръбни системи. идеален за приложения с бойлер.
Batteries Required? ‎No
Color ‎Brass x Stainless Steel
Country of Origin ‎China
Customer Reviews 4.0 4.0 out of 5 stars 58 ratings 4.0 out of 5 stars
Item model number ‎EVGG0200-OM
Item Package Quantity ‎1
Item Weight ‎3.57 pounds
Manufacturer ‎Midline Valve
Material ‎Stainless Steel,Brass
Measurement System ‎inch
Part Number ‎EVGG0200-OM
Product Dimensions ‎2 x 1 x 1 inches
Style ‎2" FIP

3

8 Review
5 Star
64
4 Star
7
3 Star
11
2 Star
0
1 Star
17

Напишете вашето мнение

Вашият имейл няма да бъде публикуван. Всички задължителни полета са маркирани с*

Scritto da: Amazon Customer
so far so good give it 5 years to tell if it is working
stainless section was magnetic, hope it is compatible with the stainless nipple on my expansion chamber
Scritto da: WoodCrafter
As described
Seems to the job it was designed for.
Scritto da: mike smith
That it was stainless steel not galvanized steel.
to install stainless steel expansion tank on a water heater.
Scritto da: Hobbyist
Not made of stainless steel or not corrosion resistant steel...
This clogged up totally in about 4 months. The elbow, attached to the "stainless" union, is shown here for reference. It is stainless steel and has zero corrosion. The union is deteriorated beyond belief and unsalvageable. The union was connecting the steel tank and stainless elbow to the copper piping with a bronze/brass compression 3/4" to 3/4" MPT on the copper side of the union. The black rubber neoprene seal and the red plastic insulator inside the large nut were all in place and assembly lubricant was applied per the manufacturer's recommendations. Don't bother with this one. You'll be replacing it in no time!
Scritto da: James Richard
Poor thread fit
The nut to tighten the center transition to the hot water heater was slightly larger than the threads. Result was bad leak...un- usable.
Scritto da: doubleu
Not stainless steel
I didn't install it because it was not stainless steel. It did not pass the magnet test. It may be galvanized at best. And it appears to have been slightly used. But I would have kept it if it was stainless steel as advertised. Other than that it looked of good quality.
Scritto da: Harold Wood
Wrong part
I dislike the fact that it's the wrong part and a three-quarter by three-quarter and not a three-quarter thread by half sweat. Parts useless and why do the advertise for a part they dont have?
Scritto da: Amazon Customer
Not stainless steel
Not stainless steel. Description and material both state "stainless steel" but really these are normal steel galvenized on exterior surfaces. I had them installed for several days when filters began collecting rust and exterior surfaces also turned white and powdery. Inside surfaces are rusted.

Свързани продукти

Открийте нашата международна мрежа

Изпращаме до 28 държави, над 200 000 продукта. Бъдете в течение, абонирайте се за бюлетина.

Array