3M Scotchlok Moisture Guard Устойчив на атмосферни влияния, UV-устойчив конектор за 2-3 проводника, 16-14 AWG (плътни/нишки), 25 в торба

Brand:3M Electrical Markets Division

3.5/5

lv
171.11

Насладете се на превъзходна безопасност и удобството на вграденото USB зареждане в първия по рода си контакт! Перфектен за добавяне на модерна свързаност навсякъде, включително части от дома, където се изисква защита от заземяване (кухни, бани, перални и т.н.). Този контакт улеснява виждането и нулирането на прекъсванията на електричеството точно там, където се случват, като същевременно осигурява две USB връзки за поддържане на зареждане на телефони или таблети, без да е необходим обемист адаптер.

Няма налични единици
Използвайте с обикновени видове термопластични изолации, само медни проводници. Работна температура 221F (105C) с максимум 600 волта за строителна жица и максимум 1000 волта за табели, тела и осветителни тела. C Вписан в UL и RoHS 2011/65/EU съвместим и UL94 V2. Побира 16-14 AWG плътни/жилни, 12 многожилни (външни) и 18 твърди/жилни, 20 многожични (вътрешни). Устойчива на атмосферни влияния конструкция, идеална за приложения, изискващи влага и UV защита. Грес на основата на минерално масло създава устойчиво на влага уплътнение за защита на връзката.
Brand 3M Electrical Markets Division
Connector Type Idc
Contact Material Polycarbonate
Gauge 14.0
Insulation Material Polycarbonate

3.5

13 Review
5 Star
72
4 Star
11
3 Star
6
2 Star
7
1 Star
4

Напишете вашето мнение

Вашият имейл няма да бъде публикуван. Всички задължителни полета са маркирани с*

Scritto da: BlackLab
Best wire connectors!
If you own a trailer you need these connectors.
Scritto da: BlaineInSussex
One and done splices
I bought these for a low voltage landscape lighting installation. The main trunk line was #12/2 and the fixture wires were #16/2. I had no confidence in the supplied insulation piercing connectors attached to the end of the fixture pigtails [ from a home center starting with the letter L ] so I cut them off and used these. 3M has been making products like this for years for the telephone utility market, these are just bigger. The outer ports will accept up to #12 AWG wire, but if you're using low voltage landscape wire, you will need to open up the insert holes (grey cap on one end) to accept the larger insulation diameter. I used a center punch. The bottom side, which you can't see in this photo, is clear plastic so you can make sure the wires are fully inserted BEFORE you squeeze. Use a pair of Chanellocks to make sure the connector is fully closed. You will probably want to wear disposable gloves and have some paper towels nearby as the silicone gel filling will ooze out when you squeeze the connector. This gel is both an insulator and a water repellent. These connectors are rated for direct burial at voltage up to 150V.
Scritto da: Byron Nevins
Waterproof and easy to use
I tried 4 different connectors for landscape lights. What a nightmare the other ones were. These are FANTASTIC. Highly recommended. It almost makes adding connectors fun! They are worth every cent that they cost. TIP: The holes you push the wires through are VERY tight (which you WANT). What I did was cut the wires at an angle. It made it much easier to insert and the angled portion goes all the way to the end and isn't involved in the electrical connection that's made when crimping. I used 14 AWG stranded wire. I haven't tried 12 AWG wire yet.
Scritto da: Chris
One of few that work with 12 AWG cord
I am using these with landscape lighting's 12 AWG cord. Most is direct burial so these connectors work very well. They have three wire ports, 2 for the in/out of the 12 AWG and the third, 16 AWG, for the light being installed. Lots of gel to protect the connection and no wire prep is needed. Just cut the wire, insert into connector, and clamp the connector to make connection and snap the top and bottom parts together
Scritto da: Srini Raman
Hack to make Wire insertion easier...
This Connector works very well once I figured out how to use it. I noticed that other users also had difficulty in inserting the wires into the connector. After struggling with the same issue on the first few wires, I sharpened each wire like a pencil with a utility knife and insertion was very easy. Yes, you need Channel Lock Pliers to Crimp it down all the way and make good connections. I also agree the Waterproof Gel does ooze out and make a mess. But, that is confirmation that you crimped the wires !
Scritto da: RUSSELL BUSHMAN
Really easy to use
takes a couple to get the hang of it, but really easy to use. My neighbor recommended these and I was happy with them.
Scritto da: Jason in Portland
Top shelf
Worked great on 14 gauge stranded and the thin wire from low voltage outdoor lights. Super secure connection. They are expensive but I'm glad I used these over other options.
Scritto da: Lilybean
The best product available for the job!
Best product available for landscape light wiring. Does the job right the first time. It will take effort to snap closed (I used a rubber mallet and small board - not enough strength in my hands to squeeze and the tool made especially for these is too $$$). Note that no stripping is required! Plan to waste a few trying getting the hang of it and double check before you close them - not really made for reuse.
Scritto da: Derrick
Top 3M quality!
Worked great for fixing some underground low voltage landscape wire for my lights Update! So I've used a few more of these and figured out a little trick, most of the led landscape lights have super thin wires, (22g or so) had a couple of tough ones to actually make the splice / connection inside, so what I do now is strip the lights wires and weave / twist in an additional striped 16-18g wire (just the ends obviously). Then feed BOTH wires into the centre hole and once I get in I cut the sacrificial 18g wire so that it ends just inside the connectors rubber seal. Makes a solid connection and had ZERO problems with them since!
Scritto da: Amazon Customer
Better than marrettes
Once you figure these out, they are way better for outdoor use than marrettes and electrical tape. Be aware that you really have to stuff the wire into the end to get it into the connector -- better than it being loose! I was using larger gauge wire so I had to strip off the insulation to get it to fit.
Scritto da: Rick
fast shipping
As promised nobody beats 3m
Scritto da: Tony
Great product
Easy to use and great for landscape lighting connections
Scritto da: JAEYOUNG KIM
Four Stars
It's good and convenient.

Свързани продукти

Открийте нашата международна мрежа

Изпращаме до 28 държави, над 200 000 продукта. Бъдете в течение, абонирайте се за бюлетина.

Array